Welcome to APS Tube Pneumatic Cleaning (Tangshan) CO.,LTD.
Service Hotline:+86-13903378238/13363292803 Chinese丨English
APS TUBE PNEUMATIC CLEANING
APS TUBE PNEUMATIC CLEANING

hydraulic tube inner wall cleaning solutionIndustry News

Industry News

Hydraulic Pipe Contamination Hard to Remove? Custom Cleaning Solutions from Sponge Projectile Manufacturer

Source :APS TUBE PNEUMATIC CLEANING (TANGSHAN) CO.,LTDTime :2026-11-17

As the core component of hydraulic transmission systems, the inner cleanliness of hydraulic pipes directly determines equipment stability, service life and failure rate. Residual hydraulic oil sludge, welding slag, metal debris and oxidation rust inside pipes are the main causes of valve sticking, abnormal oil temperature, component wear and system breakdowns.

ScreenShot_2026-10-17_112915_122

1. Background: Pain Points of Traditional Cleaning Methods

Pipe cleanliness is the bottom line for stable operation of hydraulic systems. However, conventional cleaning methods have long-standing drawbacks:

表格

MethodCore Pain Points
Soaking / BrushingLow efficiency. It takes over 10 minutes to clean a 1-meter hose; elbows and reducers cannot be reached.
Chemical Cleaning AgentsRisk of residual corrosion on hose inner walls, contaminating hydraulic oil and accelerating component wear. High cost for waste treatment and poor environmental performance.
High-pressure Water JettingLimited by elbows and tees, cannot run through the full pipe. Secondary rust will form from residual moisture.

Dry physical cleaning is the optimal solution for hydraulic pipe cleaning.

2. Core Technology: High-density Sponge Projectile + Pneumatic Cleaning Gun

Sponge projectiles are made of high-density polyurethane. Their outer diameter is 10%–20% larger than the pipe inner diameter. When pushed inside, they fit tightly against the pipe wall to deliver 360° full-contact scrubbing without blind spots.

Main Manufacturers & Product Portfolio

  • Aoboshi (AM-2 / AM-100) PSI professional pneumatic cleaning gun, applicable for pipes 6–100 mm. Lightweight aluminum alloy body (only 0.8 kg), equipped with 10 customized nozzles. Achieves cleanliness above NAS 1638 Class 6.
  • Shanghai Yuxuan Marine Technology Pipe cleaning host + high-density sponge projectiles, QXZJ cleaning gun. Universal cleaning gun and sponge projectile kits, easy to operate. Dry firing test checks sealing performance, ideal for mass cleaning jobs.
  • PSI (Australia) Original Technology Pioneer of global pneumatic projectile cleaning technology. Domestic R&D and production supported by Aoboshi Tangshan. Full-size specification coverage.

3. Standard Operating Procedure (SOP)

Step 1: Pre-cleaning Preparation

  • Air source: Install a 5 μm air filter. Adjust air pressure to 5.5–7.5 bar (0.6–0.8 MPa). Air receiver volume shall be at least 8 times the pipe internal volume.
  • Hose pretreatment: Drain accumulated water and residual hydraulic oil. Inspect for cracks or blockages; remove end fittings completely.
  • Equipment assembly: Select matched nozzles (e.g. HN6–HN50) based on hose ID and lock tightly. Load the correctly sized sponge projectile into the holder.
  • Dry firing test: Check air supply, cleaning unit and pipe connections for air leakage.

Step 2: Formal Cleaning

  • Insert nozzle firmly into one hose end and ensure an airtight seal.
  • Place a collection bucket at the outlet. Never point the outlet toward personnel.
  • Pull the trigger. Compressed air propels the sponge projectile through the pipe at high speed. The projectile spins while advancing, scraping oil sludge, rubber dust and steel wire particles off the wall.
  • For each hose, launch 2–3 projectiles repeatedly until recovered projectiles show no obvious dirt.
  • For pipes longer than 3 m or with complex bends, clean from both ends to eliminate residual blind spots.

Step 3: Post-cleaning Handling

  • Shut off air supply, disassemble nozzle and holder, and clean the equipment.
  • Dry recovered sponge projectiles and store in a sealed toolbox away from light, placed at least 0.5 m above ground for moisture protection.
  • Verify cleaning quality with borescope inspection.

4. 3-Stage Tiered Cleaning Logic

  1. Hard Scale Removal – Abrasive Sponge Projectiles For pipe rust, welding slag and hardened oil deposits.
  2. Moderate Oxidation Removal – Friction Sponge Projectiles For moderate oxide layers and carbon buildup.
  3. Precision Finishing – Standard Sponge Projectiles Capture fine residues to meet NAS 1638 Class 6 or higher.

Note: After using abrasive/friction projectiles, run 1–2 passes with standard or ultra-clean projectiles to eliminate leftover contaminants.

5. Troubleshooting Guide

表格

FaultSolution
Projectile stuck and lost inside pipeDo NOT fire more projectiles. Inject water for lubrication from the inlet, then push it out with compressed air from the opposite end.
Projectile fails to launchSwitch to a smaller-size projectile or replace the nozzle.
Recovered projectile is torn/damagedIndicates burrs, welding spurs or hard foreign objects inside the pipe. Launch a soaked matching projectile to sweep through and inspect internally.
Fully blocked pipeProbe passage with low-pressure air first. Try projectiles from small size up. If still blocked, soften deposits with eco-friendly solvent before pigging.
Projectile jammed due to excessive pressureStrictly maintain working pressure at 5.5–7.5 bar. Overpressure causes jamming while underpressure reduces scrubbing power.

6. Solution Benefits: Cost Reduction & Efficiency Improvement

表格

ItemTraditional MethodSponge Projectile Cleaning
Single hose cleaning time10+ minutesWithin 30 seconds, 8× productivity boost
Labor requirementMultiple workersSingle operator, cuts labor cost by over 60%
Hydraulic system failure rateHighReduced by 70%
Chemical residueRisk of contaminationZero chemical residue
Projectile reusability—10–15 cycles if intact
Compatibility with fittingsPoor, dead cornersFully works for 90° elbows, T-joints and U-coils

7. Wide Application Scenarios

  • Construction Machinery: Excavator & loader hydraulic hose maintenance and replacement cleaning
  • Marine & Offshore: Overhaul cleaning for deck hydraulic lines and winch piping; dry cleaning prevents salt-induced rust
  • Aerospace & Defense: Ultra-high cleanliness cleaning for actuator hydraulic pipes and servo systems
  • Coal Mining: Downhole high-pressure pipe maintenance, removing coal dust and emulsified oil sludge
  • Food & Pharmaceutical: Oil removal (single-use projectiles required to meet hygiene standards)
  • HVAC & Underfloor Heating: Compatible with PE, copper and stainless steel pipes, no wall damage
  • Nuclear & Wind Power: Periodic maintenance for long main hydraulic headers and cooling loops

Conclusion

One sponge projectile plus one pneumatic cleaning gun delivers hydraulic pipe cleaning with zero chemical residue, zero wastewater discharge and zero pipe wall damage.

From 6 mm precision servo tubing to 100 mm industrial main piping, dry physical pigging technology originated from Australian PSI and has mature local product lines from Aoboshi, Shanghai Yuxuan and other manufacturers. It achieves fast, safe, eco-friendly and cost-effective pipe cleaning in one integrated solution.

WeChat / WhatsApp: 13903378238